Devices You Need to Set Up a New Bathtub
Devices You Need to Set Up a New Bathtub
Blog Article
Are you hunting for selective information about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is additionally a moderately challenging job. If the old bathtub is readily easily accessible, the task can move quickly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. Make certain you have actually certified on your own for the job as well as fit trying it. Rather than hiring a contractor to take over a halfway-completed job, it is far better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will assist you set up a new tub in your washroom if you have actually currently acquired a brand-new bathtub and also don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable tap connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been utilized at the very least when as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is a good idea to fit the tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads about Installing A Bathtub, I was thinking sharing that article post was a great idea. Appreciated our piece? Please share it. Let other people discover it. I thank you for reading our article about Tools You Need to Install a New Bathtub .
Schedule Service Now
Report this page